CVE-2026-90591

The NXP ENET-QOS Ethernet driver's receive work handler eth_nxp_enet_qos_rx() in drivers/ethernet/eth_nxp_enet_qos hands each processed descriptor back to the DMA by writing desc->read.control = rx_desc_refresh_flags, which sets OWN_FLAG and BUF1_ADDR_VALID_FLAG. RDES0 of a receive descriptor is the DMA buffer address in read format, but the hardware write-back aliases that word with the VLAN tag fields (or, for a context descriptor, the timestamp low word), so it is destroyed on every completion. The success path rewrites desc->read.buf1_addr before re-arming; the four drop paths — errored or non-first descriptor, net_pkt_rx_alloc() failure, invalid descriptor length, and net_pkt_get_frag() failure — did not, re-arming the ring slot with the write-back residue as its DMA target address. The drop paths are driven entirely by received traffic and need no privilege or special configuration. With the defaults for this driver (CONFIG_NET_BUF_DATA_SIZE of 128 and 16 receive descriptors) a single full-size frame consumes twelve ring slots and twelve K_NO_WAIT fragment allocations, so a short burst of frames sent to the device exhausts the receive pools and reaches the allocation-failure paths; a frame with a receive error, or any frame whose first descriptor was already dropped, reaches the non-first-descriptor path. Once a slot has been poisoned, the DMA writes the next frame received in that slot to an address derived from the frame's VLAN tag fields rather than to a receive buffer. On the supported MCX SoCs that address falls in flash or reserved space, so the transfer raises a fatal bus error that the driver only logs — there is no reset or recovery path — and reception stops permanently until the device is rebooted; where the write is silently discarded instead, the untouched buffer is later handed to the network stack with a length, delivering stale buffer contents as if they were a received frame. A single triggering event is enough to make the condition persistent, so an attacker able to send traffic to the device can permanently disable its network interface.

Score
CVSS 3.1 7.5 High
Status
Awaiting Analysis - vulnerabilities@zephyrproject.org
Published
2026-11-09
Last modified
2026-11-12
Weaknesses
CWE-787

Affected products

References


Your early warning system for new security vulnerabilities


Open BETA

Every day brings a flood of new vulnerabilities, roughly 100 CVEs daily. Which one will really affect you?

Attacks on known but unpatched vulnerabilities (Common Vulnerabilities and Exposures, or CVEs for short) are among the most common entry points for hackers. Companies must continuously check for such vulnerabilities. Does this affect our products? Which versions are affected? How critical is it?

As the window between publication and exploitation by attackers keeps shrinking, companies are under more pressure than ever to find a high-quality solution for managing these risks as quickly as possible. However, IT teams are heavily time-constrained, making manual tracking of all relevant CVEs nearly impossible.

100+ new CVEs per day

Most CVEs are irrelevant to your infrastructure

Time-to-exploit < 5 days

Attackers are exploiting vulnerabilities faster than ever before

Manual research is time-consuming

Vendor websites, RSS feeds, and blogs need to be searched daily

Vulnerability scanners are lagging behind

Plugin development isn't progressing fast enough to identify risks in a timely manner

CVE Alarm provides you with immediate notifications of relevant security vulnerabilities

CVE Alarm continuously monitors all newly published CVEs and automatically compares them with the products you use. You will only be notified if a relevant vulnerability affects your systems and meets your defined criteria.

Real-time notification

Direct email notification without delay

Product-based filters

Only CVEs that actually affect your infrastructure

Custom criteria

Filter by CVSS-Score, exposure, products, and vendors

Team-oriented & multi-tenant capable

Assign products or alerts to specific teams or customers

More time to act

Administrators can review and install updates faster

Time savings

No more manually reviewing the flood of new CVE information

Three steps for better patch planning

With CVE Alarm you will easily receive relevant security alerts for your infrastructure.

Subscribe To
Products

Select the IT products you use. From Apache to VMware – all critical assets are monitored.

Define
Criteria

Set product-specific filters based on criticality (CVSS ≥ 7.0 (high)). You will only receive relevant alerts.

Get
Notified

Receive an immediate notification as soon as a matching CVE appears. Recipients can be defined individually for each product.

Be faster
than the attackers

With CVE information, you have more time for patch planning and can close security gaps before they are exploited.

Designed for the target group companies and service providers

Whether a global Security Operations Center or a small IT team, CVE Alarm supports CVE monitoring for organizations of all sizes.

Companies with their own IT infrastructure

Medium-sized to large companies that need to proactively monitor their vulnerabilities

Administrators

IT professionals responsible for infrastructure security and maintenance

Security teams and cybersecurity experts

Security Operations Centers (SOCs) and Computer Emergency Response Teams (CERTs) that require CVE information for proactive security measures

Chief Information Security Officers (CISOs) & IT managers

Decision-makers who need an overview of critical vulnerabilities

Security service providers

Managed service providers (MSPs) and security consultancies that manage multiple clients and need to monitor CVEs

From experience to innovation. About us and CVE Alarm.

CVE Alarm is a product of AVABIS GmbH and was developed in collaboration with IT security experts.

AVABIS GmbH – Who are we?
We, AVABIS GmbH, are an experienced partner for IT quality assurance. Our focus is on software testing and software development. Our clients, corporations from various industries, have trusted us for more than ten years.

CVE Alarm – How did the idea come about?
In our daily project work, we repeatedly witnessed the significant uncertainty surrounding new security alerts. We saw how much time teams have to invest to determine whether a published vulnerability even affects their own system landscape. Based on these experiences, we know how time-consuming it is to gather, evaluate, and prioritize information from diverse sources under time pressure.

This made us realize that the real problem is not a lack of information, but rather an overabundance of it.

This led to the idea of ​​developing a product that enables companies to manage this information overload and maintain control over their IT security.

Developed and operated in Germany
Our systems run on German IT infrastructure, and we adhere to high security and data protection standards. This ensures data sovereignty, clear responsibilities, and reliability, especially for organizations with their own security teams or CERT structures.

Get in contact with our team

Do you have questions about CVE Alarm or would you like a personal consultation?
We're happy to help.

Please use our contact form.